Menu
From € 171,00
With its built-in Bluetooth, the BMV Smart is ready for the age of the "Internet of Things" (IoT).
Most other Victron Energy products also have Bluetooth. The wireless
communication between products simplifies the installation of systems and improves performance.
Using a smartphone or other Bluetooth-enabled device, adjust the
- adjust the settings,
- display all important data on one screen,
- display history data and
- update to the latest software when new functions are available.
All electrical connections are made using the PCB connector on the current shunt. The shunt is connected to the monitor via a standard RJ12 telephone cable. Included in the scope of delivery: RJ12 cable (10 m) and battery cable with fuse (2 m); no other components are required.
A separate front panel for a square or round display, a safety ring for rear mounting and screws for front mounting are also supplied.
A damaged cell or a damaged battery can destroy an entire large, expensive battery bank.
If batteries are connected in series, a timely warning message can be generated by measuring the midpoint voltage. Please also refer to the BMV manual, section 5.2 for more information.
We recommend our Battery Balancer (BBA000100100) to maximize the life of lead-acid batteries connected in series.
Power consumption: 0.7 Ah per month (1 mA) at 12 V and 0.6 Ah per month (0.8 mA) at 24 V
Lithium-ion batteries in particular have almost no capacity left when they are discharged to the point of
discharged until they are switched off due to low voltage.
After switching off due to low voltage, the capacity reserve of a lithium-ion battery is
is approximately 1 Ah per 1000 Ah of battery capacity. The battery will be damaged if the remaining reserve
reserve capacity is removed from the battery. A residual current of 10 mA, for example, can damage a 200 Ah
battery if the system is left in a discharged state for more than 8 days.
Prevents increased current consumption in the event of an alarm.
- Battery voltage, current, power, ampere hours consumed and state of charge
- Remaining runtime at current discharge rate
- Programmable visual and audible alarm
- Programmable relay to switch off non-essential loads or switch on a generator if required.
- One 500 amp quick connect shunt and one connection kit.
- Shunt capacity selectable up to 10,000 amps.
- VE.Direct communication port
- Stores a wide range of historical data that can be used to assess usage patterns and battery condition.
- Wide input voltage range: 6.5 - 70 V
- High current measurement resolution 10 mA (0.01 A)
- Additional input for measuring voltage (of a second battery), temperature or midpoint voltage and associated alarm and relay settings.
| Weight | 0.450 kg |
|---|---|
| Size | 69 × 31 × 69 mm |
You must be logged in to submit a review.
The technology used was developed by the Austrian photovoltaic manufacturer DAS Energy in Wiener Neustadt and essentially consists of the proprietary fiber-reinforced plastic core (prepreg). This layer is located above and below the cell and is mainly responsible for the flexibility and stability of the DAS Energy module. Monocrystalline cells are used. Further information on request.
DAS Energy modules can be glued to a smooth surface. The modules can also be attached using magnets and quick-release systems, as with the DAS Energy balcony power plant. With the golf cart PV roof, the module is attached to the roof of the golf cart using double-sided adhesive tape and screws.
As with conventional modules, shading should be avoided. Should shading nevertheless occur, all modules have bypass diodes that disconnect the shaded parts of the module to minimize yield losses.
Shading should be avoided at all costs with balcony power plants, as the module will not provide any power if it is shaded. Before purchasing a balcony power plant, it is therefore essential to check whether shading (e.g. from trees, house walls, etc.) could affect the performance of the module.
The purchased modules can be returned in their original packaging within 14 days at your own expense or directly to the store upon presentation of the original invoice receipt. Refunds will normally be madewithin one week.
14days.
Austria & Germany
For inquiries about deliveries to other EU countries, please contact us at office@daskraftwerk-pv.com.
If our modules are in stock, we deliver within 3-5 days. If the modules are not in stock, it usually takes a little longer - we are happy to provide information about current delivery times on our website and on request.
Subscribe to our newsletter to be informed about the latest trends, receive special offers and get exclusive advance information about new products.
Reviews
There are no reviews yet.