Victron SmartSolar MPPT 100/20 charge controller

From  96,90

Contains VAT.
Direct shipping within AT and DE.
For shipping to other EU countries please contact us
Zubehör sind nur bei gleichzeitigem Erwerb von PV-Modulen USt. befreit.

Die bloße Nachrüstung einer bestehenden Anlage unterliegt hingegen dem Normalsteuersatz

Bei der Auswahl und Bestellung von Artikeln mit 0% bestätigen Sie, dass Sie die Voraussetzungen für den 0% Steuersatz gemäß § 28 Abs. 62 UStG 1994 (Österreich) oder gemäß § 12 Abs. 3 UStG (Deutschland) erfüllen.
Item number: VIC_0000002

Categories: Accessories

Description

Built-in Bluetooth Smart

The wireless solution for setting up, monitoring and updating the SmartSolar charge controller.

VE.Direct

For a wired data connection with a Color Control GX, other GX products, a PC or other devices.

Ultra-fast maximum power point tracking (MPPT)

Especially in cloudy weather, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield by up to 30 % compared to PWM charging controllers.
by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers.

Load output

A deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the
loads when the battery has been discharged to a predefined voltage value.
(48 V model: interface to a relay) Alternatively, an algorithm for intelligent battery management can be selected: see BatteryLife. The
load output is short-circuit proof.

Battery Life: intelligent battery management

If the solar charge controller is not able to charge the battery to its full capacity within one day, the status of the battery
constantly switches back and forth between "partially charged" and "end of discharge". This operating mode (no regular full charging) will damage a lead-acid battery within
lead-acid battery within a few weeks or months.
The BatteryLife algorithm monitors the state of charge of the battery and, if necessary, raises the threshold for disconnecting the load on a daily basis
(i.e. the load is disconnected earlier) until the energy gained is sufficient to charge the battery to almost 100%. From this point
the threshold for disconnecting the load is modulated so that charging to almost 100% is achieved approximately once a week.

Programmable battery charging algorithm

Further information on this can be found in the Software section of our website.

Day/night time control and light dimming option

Further information on this can be found in the Software section of our website.

Internal temperature sensor

Equalizes constant and charge retention voltages according to temperature.

Option external battery voltage and temperature measurement via Bluetooth

A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to transmit the battery voltage and temperature data to one or more SmartSolar charge controllers.
one or more SmartSolar charge controllers.

Recovery function for fully discharged batteries

Will initiate charging even if the battery has been discharged to zero volts.
Will reconnect to a fully discharged lithium-ion battery with internal disconnect function.

 

Downloads

SmartSolar MPPT 75/10, 75/15, 100/15, 100/20-48V data sheet (PDF)

 

Technical data:

  • Model: MPPT 100/20
  • Battery voltage: 12/ 24/ 48 V
  • Nominal charging current: 20 A
  • Nominal PV power (12 V): 290 W
  • Nominal PV power (24 V): 580 W
  • Nominal PV power (48 V): 1160 W
  • Short-circuit current: max. 20 A
  • PV open-circuit voltage: max. 100 V
  • Peak efficiency: 98%
Weight 0.65 kg
Size 98.6 × 131 × 64 mm

Reviews

There are no reviews yet.

Be the first to review "Victron SmartSolar MPPT 100/20 charge controller" Cancel reply

FAQ

The technology used was developed by the Austrian photovoltaic manufacturer DAS Energy in Wiener Neustadt and essentially consists of the proprietary fiber-reinforced plastic core (prepreg). This layer is located above and below the cell and is mainly responsible for the flexibility and stability of the DAS Energy module. Monocrystalline cells are used. Further information on request.

DAS Energy modules can be glued to a smooth surface. The modules can also be attached using magnets and quick-release systems, as with the DAS Energy balcony power plant. With the golf cart PV roof, the module is attached to the roof of the golf cart using double-sided adhesive tape and screws.

As with conventional modules, shading should be avoided. Should shading nevertheless occur, all modules have bypass diodes that disconnect the shaded parts of the module to minimize yield losses. 

Shading should be avoided at all costs with balcony power plants, as the module will not provide any power if it is shaded. Before purchasing a balcony power plant, it is therefore essential to check whether shading (e.g. from trees, house walls, etc.) could affect the performance of the module. 

The purchased modules can be returned in their original packaging within 14 days at your own expense or directly to the store upon presentation of the original invoice receipt. Refunds will normally be madewithin one week.

Austria & Germany

For inquiries about deliveries to other EU countries, please contact us at office@daskraftwerk-pv.com.

If our modules are in stock, we deliver within 3-5 days. If the modules are not in stock, it usually takes a little longer - we are happy to provide information about current delivery times on our website and on request.

Product search